It’s also helpful (but not necessary) to remove the frame from the monitor. The whole idea was to spend less time on. She uses it every morning and night when shes getting ready, he explains. Toothie96 built the DIY magic mirror as a gift for his significant other. Something thinner and lighter is better, but this monitor by Sceptre would work. His hi-tech creation displays information like the time, date, weather forecast, and news all on its facea contemporary riff on the fairy tale. Later, I'll connect the speaker via bluetooth and set it next to the mirror or something. To get started you’ll need the following: A monitor: Preferably at least 24 inches, and one you don’t care about losing. It's not as loud or clear as the bluetooth speaker, but it will work for now. In this photo, you can also see the space where I was going to put my bluetooth speaker - I measured things (slightly) incorrectly and it won't fit, so I'm going to use the monitor's built-in speaker. This one cost me about $8, so I don't have very high hopes for it. If you can find a flush mount microphone that's good, go ahead and do that. I didn't want to drill a hole in the face of the mirror and ruin the look, although that would probably be the best location for a microphone. The microphone itself is flexible, so if it doesn't pick up sound properly I can always pull it out further and curl it around the bottom of the mirror. Next, press the Alt button on your keyboard, then go to files and quit the program to do your customizations. Finally, you should be able to see info like the time, news headlines, messages, and more as shown below. I put it in the bottom of the mirror where you won't see it. Once Magic Mirror is fully installed, it will start up on its own. Next, I drilled a hole for my microphone. Eventually I want to install a power outlet behind the mirror, but for now I can be lazy and power it this way. I used my dremel and a multipurpose bit to cut a small slot at the bottom to run a power cord through. The total cost for this project (including the wood, monitor, Raspberry Pi, and mirror) was around $300-350. The box/frame houses all the components, including the microphone, and looks pretty. The Raspberry Pi is a small, credit card-sized computer that powers the whole thing, displaying the Magic Mirror interface and running Jasper, the voice-control system. I also recommend a monitor with built-in speakers, but this is optional. I recommend an LED monitor for minimal power consumption, maximum crispness, and to prevent mirror glow at night. Select your network, enter your wifi password, and click OK. In the top right of your screen, click on the network icon (two computers with an X). Order the thicker mirror option (3/16") to prevent a "funhouse mirror" effect. This DIY magic mirror displays helpful information on its face. Our Magic Mirror needs to be wifi-enabled so that it can connect to the internet and so that we can access it remotely to set things up. I ordered my mirror through Tap Plastics ( this one). The two-way mirror is made of acrylic and sits flush over the monitor, allowing the graphics on the monitor to shine through while maintaining a mirror effect. Then after you’ve updated you want to update the Magic Mirror library- because it will likely show updates are available once it is loaded. There are a few things you want to do in the console now so run this line of code to update Raspian: sudo apt-get update. The attached highly technical drawing illustrates how these components work together. Step 4: Update Raspberry Pi and Magic Mirror. What took way more time was to run tests of modules, customize to our preferences and obviously hack our way out to something that would agree with all tastes in the house.There are four major components to the voice-controlled smart mirror. All you need is the Magic Mirror software, a 2-way mirror, an ornate. This part, for me at least, was not really difficult to achieve, the whole install was running in no time, probably I have spent something like 2 hours to make the whole process, including making the image of the RPi rotate and appear "vertically" on the monitor. If you have an old laptop lying around, put it to use with this amazing DIY project. This browser would then connect to a local webserver on the RPi providing the MagicMirror2 software. The main idea is to use an Raspberry PI version 2 I had sitting around the house, which connected to a dedicated monitor via HDMI, would boot and automatically login to a user and run some browser in kiosk mode. While the wood product was taking shape, I was also working in the software part of the project. I actually failed in properly document the whole project, as I was more focused into build something that would work accordingly.īut even the picture with the whole frame out of focus, I think it is reasonable to have an idea about the overall result.
0 Comments
Leave a Reply. |